
10 Sep 2026
A fish plate in railway track is a shaped steel bar bolted to the rail web where two rail ends meet, holding those ends in line and carrying the wheel load across the discontinuity. Fish plates are fixed in rail tracks to minimise the gap between rail ends, keep the running surface level and damp the vibration that every passing axle generates at a joint. IB Group supplies railway fish plates in the 1R65 and 2R65 types, produced to EN and GOST standards.
A fish plate — also called a joint bar, splice bar or rail joint connector — is always used as a pair. One plate sits against the inner face of the rail web and one against the outer, and joint bolts passed through matching holes draw the assembly together. The plate does not simply cover the gap: it restores a large part of the bending stiffness the rail loses where it is cut, so a wheel crossing the joint is supported rather than dropped into a void.
People who search for what is a fish plate in construction mean the same idea in another material: in structural steelwork a fish plate is a splice plate bolted across a butt joint in a beam or column so the joint can transfer force. The railway version applies it to a rolled rail section.
Rail steel expands and contracts with temperature, and bolted track absorbs that movement in the expansion gaps left at each joint. The rail end is a free edge, so the wheel meets a step, not a continuous surface. Over time this produces the familiar failure sequence: end batter on the rail head, a dipped joint as the sleepers beneath it are hammered down, accelerated ballast attrition, and fatigue cracking that starts at a bolt hole. Everything a fish plate is asked to do follows from this: hold both rail ends in vertical and lateral alignment under load, allow controlled longitudinal movement, and survive repeated impact without being so hard that it wears the rail it holds.
The 1R65 and 2R65 plates use a double-headed section. The upper head bears against the underside of the rail head and the lower head against the top surface of the rail foot, along the inclined surfaces usually called the fishing angles. When the joint bolts are tightened, both plates are wedged into those angles from either side, which is what produces the rail compression the product description refers to.
That geometry explains why a plate is profile-specific. The load path runs mainly through friction generated by bolt tension and contact on the fishing angles, not through shear on the bolt shanks, so a plate that fits one rail section sits loosely against another even if the rails weigh the same per metre. More bolts spread the clamping force over a longer surface and leave the joint stiffer.
The two types IB Group supplies cover the standard wide-gauge cases: the 1R65 plate connects R65 rails and is produced in six-hole and four-hole versions, while the 2R65 plate connects R65 and R75 rails during construction or repair of wide-gauge track.
| Type | Rails connected | Length | Bolt holes | Weight per unit | Steel | EN standard | GOST standard |
|---|---|---|---|---|---|---|---|
| 1R65 | R65 | 1000 mm | 6 (or 4) | 29.26 kg | K54, E54 | EN 10025-2:2019 | GOST 8193-73, GOST 33184-2014 |
| 2R65 | R65, R75 | 800 mm | 4 | 23.78 kg | M54 | EN 13674-1:2020 | GOST 33184-2014 |
Unit weight drives freight planning and handling. Every joint takes two plates, so a 1R65 joint carries 58.52 kg of steel before bolts are counted and a 2R65 joint carries 47.56 kg. On a line laid with 25 m rails there are forty joints per rail line per kilometre — eighty plates per rail line, one hundred and sixty for a kilometre of single track.
The steel grade is where the two documentary systems diverge most visibly. The 1R65 plates are manufactured from K54 and E54 grades, produced from open-hearth steel with low carbon content, and are certified against GOST 8193-73 and GOST 33184-2014 as well as EN 10025-2:2019. The 2R65 plates are manufactured from M54 grade using special rolled profile strips and comply with GOST 33184-2014, with EN 13674-1:2020 quoted on the international specification.
Low carbon content is a deliberate choice, not an economy. A joint bar absorbs impact and carries a stress concentration around each bolt hole, so toughness matters more than raw hardness, and a plate harder than the rail it clamps would transfer wear into the rail head. This is the opposite of the logic applied to railway rails, where head-hardened grades are chosen precisely to resist wear.
For a buyer, EN and GOST are not competing quality levels but two certification regimes with different grade nomenclature. The same physical plate can satisfy both, but the paperwork must be agreed in the contract, not assumed.
Matching is done by rail profile designation, not by nominal rail weight. Start with the rail section actually in the track — R65, R75 or a European profile — then select the plate type whose fishing angles and hole pitch correspond.
Where two different profiles must be joined permanently, a transition arrangement is required rather than a standard plate, and that case belongs at the design stage. Track gauge is a separate question again: both the 1520 mm CIS gauge and the 1435 mm European standard gauge appear in regional projects.
Modern main lines are largely laid as continuous welded rail, where rail ends are joined by flash butt welding instead of being plated: no gap, no impact, far less maintenance. Our rail flash butt welding machines cover both stationary and mobile on-site welding for line repair and junction modernisation.
That does not make the fish plate obsolete. Bolted joints remain standard practice for temporary connections during construction, for insulated joints at signalling and track-circuit boundaries, for emergency repair of a broken rail, in sidings and industrial spurs where welding is not economic, and around switches and turnouts, where the geometry makes bolted connections practical.
A specification that avoids rework contains the rail profile and its governing standard, the plate type, the hole count and length, the certification regime (EN or GOST) with the exact standard number, the steel grade, the quantity in plates or joints per kilometre, the matching joint bolts and washers, any coating, and the mill documentation the project requires. IB Group supplies both standard and customised plates.
Commercial terms are confirmed per order at the quotation stage, since they depend on quantity, certification and destination. For projects that need more than materials, the railway construction service covers installation and technical support alongside supply, as in the Sumgayit-Yalama railway reconstruction. Send the rail profile, the standard and the approximate tonnage through the contact page to have the specification checked before a purchase order is issued.
A fish plate is a shaped steel bar bolted to both sides of the rail web where two rail ends meet. Working as a pair, the plates hold the rail ends in alignment and transfer the wheel load across the gap. Their primary function is to minimise the gap between rails and reduce the vibration caused by moving trains, which extends the service life of the track and reduces maintenance cost.
Size and weight depend on the rail profile the plate serves. The 1R65 plate for R65 rails is 1000 mm long, has six bolt holes and weighs 29.26 kg per unit; a four-hole version is also produced. The 2R65 plate for R65 and R75 rails is 800 mm long, has four holes and weighs 23.78 kg. Every joint takes two plates, so a 1R65 joint is 58.52 kg of steel and a 2R65 joint 47.56 kg.
The 1R65 plates are made from K54 and E54 grades, produced from open-hearth steel with low carbon content, and certified to GOST 8193-73, GOST 33184-2014 and EN 10025-2:2019. The 2R65 plates are made from M54 grade using special rolled profile strips and comply with GOST 33184-2014, with EN 13674-1:2020 on the international specification. Low carbon content gives the toughness a joint bar needs to absorb impact and resist cracking around the bolt holes.
Every joint uses two plates, one on the inner face of the rail web and one on the outer, drawn together by joint bolts passed through both plates and the rail. A six-hole arrangement takes six bolts with nuts and spring washers, a four-hole arrangement four. Bolts, nuts and washers are ordered alongside the plates from the railway accessories range, since the plate alone does not form a working joint.
Yes. Continuous welded rail removes most running joints by flash butt welding the rail ends, but bolted joints remain necessary for temporary connections during construction, for insulated joints at signalling and track-circuit boundaries, for emergency repair of a broken rail before welding can be scheduled, in sidings where welding is not economic, and around switches and turnouts.

13 Sep 2026
What API 5CT actually covers, why threads sit in API 5B, where API 5L begins, how J55 to P110 grades read, how LTC, BTC, EUE and premium connectors differ, and what to require on delivery.

07 Sep 2026
Which valve family fits which duty, how pressure and temperature decide between carbon and stainless steel bodies, what API 6D, EN 12516, EN 593 and GOST 33259 govern, and the checklist to send with an enquiry.

07 Sep 2026
Six pipe families, three standard systems and one purchase order. A practical guide to oil and gas piping supply — boiler, OCTG, seamless, coated and insulated pipe — and what a complete enquiry must state.