
23 Aug 2026
Railway turnouts and switches are the permanent-way assemblies that let a train leave one track and join another. A turnout is not a single product but a designed assembly — switch blades, closure rails, a crossing, guard rails, bearers and a drive — in which every part is dimensioned to a specific track gauge, rail profile and crossing angle. That is why a turnout cannot be ordered from a catalogue line the way a rail or a bolt can: it is manufactured to a drawing, and the drawing has to be settled before anything is cast or forged.
This article explains the anatomy of a turnout, what the turnout mark actually tells you about speed through the diverging route, how 1435 mm and 1520 mm networks differ in practice, why crossing metallurgy dominates the wear behaviour of the whole assembly, and what has to be confirmed before manufacture. IB Group supplies the full range of railway switches and turnouts to GOST and EN standards for mainline, metro, tram, port and industrial projects, including work for Azerbaijan Railways.
Read left to right in the direction of travel, an ordinary turnout has five functional zones plus the equipment that operates it.
The mark — written 1:9, 1:11, 1:12 or 1:14 in EN practice and 1/9 or 1/11 in GOST practice — is the tangent of the crossing angle: one unit of lateral offset for every nine, eleven, twelve or fourteen units measured along the track. It is the single number that governs how the turnout behaves.
A higher second number means a shallower angle, a longer turnout, a larger radius through the diverging route, and therefore a higher permissible speed on the diverging move. It also means more length, more steel, more bearers and more space in the track layout. The choice is a trade-off, not a preference: a 1:9 turnout is compact and suits depot throats, industrial sidings and yard work where diverging speeds are low, while flatter marks such as 1:12 and 1:14 belong where trains take the diverging route at meaningful speed. The straight route through any of them is governed by the line speed, not by the mark. IB Group supplies ordinary, curved and symmetric turnouts, the symmetric type splitting the difference between the two routes rather than favouring one.
Azerbaijan and the wider CIS network operate on 1520 mm gauge, while EU, Turkish and most international projects use 1435 mm. This is not a dimension that can be adjusted at the margin — gauge changes the rail profile, the standard, the mark notation and the crossing designation together. The table below shows how the same product, an ordinary railway turnout, is specified in each world.
| Parameter | EN / international | GOST |
|---|---|---|
| Standard | EN 13232 | GOST 33535-2015 |
| Track gauge | 1435 mm | 1520 mm |
| Rail profile | 49E1, 54E1, 60E1 | R50, R65 |
| Crossing angle / mark | 1:9, 1:12, 1:14 | 1/9, 1/11 |
| Crossing steel | Cast Mn13 (austenitic manganese) | 110G13L (GOST 7370) |
| Crossing type | Assembled / rail-bound | Cast / rigid crossing |
The practical point for a procurement engineer is that the standard and the gauge must be stated together at enquiry stage. A 1:11 mark exists in GOST practice and a 1:12 in EN practice; asking for "a 1:11 on 1435 mm" produces a drawing query rather than a quotation. The same discipline applies to the rail profile of the running line, because the turnout has to match the rails it is being welded or fished into.
The crossing is where turnouts fail, so it is where the metallurgy is concentrated. Cast manganese steel — Mn13 under EN designation, 110G13L under GOST 7370 — is austenitic: it is relatively soft as delivered and work-hardens dramatically under the repeated impact of passing wheels, developing a hard surface layer over a tough core. That combination is what allows a single cast component to survive impacts that would spall a conventional rail steel.
Crossings come in two families. A fixed crossing leaves the flangeway gap open and relies on the guard rail to steer the wheel across it; it is simple and robust, and it is the standard solution on GOST cast rigid crossings. A movable crossing closes the gap mechanically so the running surface is continuous, eliminating the impact entirely at the cost of another moving, signalled mechanism. Diamond crossings under EN 13232-5 are available in both fixed and movable form.
Switch blades follow a different logic. They are not impact components but wear and contact-fatigue components, so they are forged from rail steels — 60E1 or 54E1 sections in grade R350HT, a heat-treated grade also used on the plain-line rails of heavily loaded routes, while R260 appears where the duty is less severe, as on derailing switches. Matching blade steel to the hardness of the adjoining running rail matters: a large hardness mismatch at a weld or joint produces a step as the softer side wears down faster.
"Turnout" is the headline product, but a station throat or an industrial yard needs several other assemblies built on the same components.
| Assembly | What it does | Key parameters |
|---|---|---|
| Railway turnout | Guides a train from one track to another; ordinary, curved and symmetric types | EN 13232 / GOST 33535-2015; 1:9, 1:12, 1:14 or 1/9, 1/11; cast Mn13 or 110G13L crossing |
| Crossover | Connects two parallel tracks in both directions; consists of four turnouts | EN 13232 / GOST 33535-2015; double crossover; station throats, depots, industrial junctions |
| Single crossover | Links two parallel tracks in one direction; consists of two turnouts | EN 13232; 1:9, 1:11; station, industrial and port lines |
| Diamond crossing | Two tracks intersect at the same level | EN 13232-5 / GOST 7370; 1:9, 2:9 or 2/11, 2/9; fixed or movable crossing |
| Expansion (equalizing) joint | Compensates thermal movement of continuously welded rail and bridge transitions | EN 13232 / EN 13674; 54E1, 60E1 or R50, R65; displacement range ±100–600 mm; R260, R350HT |
| Derailing (releasing) switch | Deliberately derails a runaway wagon before it reaches the mainline | EN 13232; manual, electric or interlocked actuation; R260 |
| Portable retarder / shoe discharger | Controls and stops wagon speed on humps and shunting tracks | EN 13232; steel with hardened elements; portable or stationary |
| Turnout components | Cast manganese crossings, forged switch rails, base plates, heel and distance blocks, brackets and clamps | EN 13232 / EN 15689 / GOST 7370; for manufacture, repair and upgrade |
Two of these deserve a note. The expansion joint is the item most often omitted from a scope and most expensive to add later: with a displacement range of ±100–600 mm it is what allows continuously welded rail to meet a bridge deck without transferring the deck's movement into the track, and it belongs in the design from the start rather than being retrofitted where rail welding equipment has already produced a long welded section. The derailing switch is a safety device rather than a traffic device — it exists to sacrifice one wagon rather than allow a collision on the mainline, and its actuation type has to be agreed with the signalling engineer, not chosen on price.
Because a crossing failure closes a route, the quality regime around turnout products is stricter than for plain-line material. All products supplied by IB Group undergo non-destructive testing (NDT) and are manufactured at plants certified to ISO 9001, ISO 14001 and OHSAS 18001. For a client's engineer this is what makes the delivered assembly auditable: the certification frames the process, and the NDT records relate to the specific castings and forgings delivered. The documentation package a project requires should be agreed at enquiry stage along with the technical parameters, since it is part of what is being manufactured, not an afterthought at delivery.
A turnout enquiry that lists only "one 1:9 turnout" cannot be priced or drawn. Five parameters have to be fixed first, and a sixth usually follows:
Beyond that, the layout drawing should show the connecting geometry — which rails, welded or fished with rail joint fish plates, and the sleeper and fastening arrangement at the transitions. On larger schemes these interfaces are usually handled inside a railway construction contract or coordinated through project management services, which is how a turnout arrives on site able to be installed in the possession that was planned for it — the approach used on reconstruction work such as the Sumgayit–Yalama railway reconstruction. Quantities, scheduling and commercial terms are confirmed per order at the quotation stage; to have a layout checked against the standards above, send the drawing to our team in Baku.
In everyday use the words overlap, but they are not the same thing. The switch is the moving part — the pair of tapered switch blades, or tongue rails, that shift laterally against the stock rails to select a route. The turnout is the complete assembly that contains it: switch blades, closure rails, the crossing, guard rails, bearers, fastenings and the drive. When you buy "a turnout" you are buying the whole assembly manufactured to one drawing; when you buy "switch rails" you are buying replacement blades for an assembly that already exists.
The mark is the tangent of the crossing angle: 1:9 means one unit of lateral offset for every nine units measured along the track. A higher second number gives a shallower angle, a longer turnout and a larger radius through the diverging route, so trains can take the diverging move faster. It also takes more length and more space in the layout. Compact 1:9 turnouts suit depots, yards and industrial sidings; flatter marks such as 1:12 and 1:14 are used where the diverging route carries meaningful speed. GOST practice writes the same idea as 1/9 and 1/11.
The crossing is where the diverging rail cuts across the through rail, so there is a gap in the running surface and the component absorbs the heaviest impact loading in the whole turnout. Cast austenitic manganese steel — Mn13 under EN designation, 110G13L under GOST 7370 — is relatively soft as delivered and work-hardens under repeated wheel impact, forming a hard surface over a tough core. That combination resists both the impact and the abrasion that would quickly spall an ordinary rail steel, which is why cast manganese crossings are standard on both 1435 mm and 1520 mm networks.
No. Gauge is not a parameter that can be adjusted at the margin: it changes the rail profile, the applicable standard, the mark notation and the crossing designation together. A 1435 mm turnout is specified to EN 13232 with 49E1, 54E1 or 60E1 rails and marks such as 1:9, 1:12 and 1:14, while a 1520 mm turnout follows GOST 33535-2015 with R50 or R65 rails and marks 1/9 or 1/11. State the gauge and the standard family together at enquiry stage; they define which product family is being quoted.
Five parameters have to be fixed before a drawing can be produced: the mark or crossing angle, the hand (left or right, viewed facing), the track gauge, the rail profile of the connecting line, and the crossing type — cast rigid, assembled or rail-bound, fixed or movable. The drive and signalling interface usually follows, since manual, electric and interlocked actuation are different products. A layout drawing showing the connecting geometry lets the parameters be checked against each other, which is faster than exchanging partial specifications.

13 Sep 2026
What API 5CT actually covers, why threads sit in API 5B, where API 5L begins, how J55 to P110 grades read, how LTC, BTC, EUE and premium connectors differ, and what to require on delivery.

10 Sep 2026
What a fish plate in railway track does, how the double-headed section clamps a rail joint, 1R65 and 2R65 sizes and weights, EN versus GOST steel grades, and how to match a plate to your rail profile.

07 Sep 2026
Which valve family fits which duty, how pressure and temperature decide between carbon and stainless steel bodies, what API 6D, EN 12516, EN 593 and GOST 33259 govern, and the checklist to send with an enquiry.