
26 Aug 2026
Railway construction is the sequence of engineering works that turns a surveyed corridor into a track that can safely carry traffic: formation and drainage, ballast, sleepers and fastenings, rail laying and jointing, turnouts, bridges and tunnels, signalling, stations, and finally inspection and commissioning. Each stage is a foundation for the next one, so a defect left in the earthworks will still be visible in the track geometry years later. This guide walks through the full build sequence, explains what every stage depends on, and shows where the materials decision and the works decision meet.
Railway line construction is a technical and logistical process at the same time. A contractor is not only building a structure; it is scheduling the arrival of rails, turnouts, fastenings and welding equipment so that each crew has what it needs on the day the previous crew finishes. IB Group's railway construction service covers the stages below as sub-projects — earthworks and land preparation, ballast laying, rail and fastening installation, bridges and tunnels, signalling, stations and auxiliary facilities, and final inspection and testing — planned and executed in compliance with international standards.
The table below summarises the build sequence and what each stage is dependent on.
| Stage | Main works | Depends on |
|---|---|---|
| Survey and alignment | Topographic and geotechnical survey, setting out curves and gradients | Route corridor, design speed, axle load |
| Earthworks and formation | Levelling, cut and fill, embankments, drainage systems | Ground conditions, groundwater, environmental constraints |
| Ballast and sub-base | Selection and laying of ballast, sub-ballast layers | A compacted, drained formation |
| Sleepers and fastenings | Sleeper spacing, tie plates, clips, anchors, rubber pads | Rail profile, gauge, traffic type |
| Rail laying | Unloading, positioning and fastening rails to gauge | Rail profile and delivery lengths |
| Jointing | Bolted joints with fish plates, or flash-butt welding into long strings | Rail lengths, welding equipment, temperature window |
| Turnouts and crossings | Assembly and alignment of switches at station throats and junctions | Crossing angle, gauge, rail profile |
| Structures | Bridges, viaducts, tunnels, culverts | Geology, span requirements, clearances |
| Signalling and control | Signalling, interlocking, traffic control systems | Completed track and structures |
| Testing and commissioning | Geometry, ultrasonic and load testing, trial runs | Everything above being finished |
Everything the traveller sees — rails, sleepers, ballast — sits on a formation that nobody sees. The survey fixes the alignment: curve radii, gradients and cant are chosen for the design speed and the heaviest axle load the line has to carry, because those two numbers drive almost every later decision.
Earthworks then create that formation by levelling the ground, cutting through high points and building embankments across low ones, with drainage installed at the same time. Drainage is the single most under-rated element of rail construction work: water trapped in the formation softens the subgrade, ballast then sinks into it, track geometry drifts, and the line needs tamping far sooner than planned. IB Group carries out land preparation with eco-friendly technologies to minimise environmental impact, and the drainage system is installed as part of this stage rather than retrofitted later.
Ballast does three jobs at once: it spreads wheel loads over the formation, it holds the track laterally and longitudinally in place, and it drains. Ballast quality and grading matter because rounded, weak or contaminated stone will not lock together and the track will move under traffic.
Sleepers transfer the load from rail to ballast and hold the two rails to gauge — 1520 mm on the post-Soviet network, 1435 mm on standard-gauge lines. The rail is held to the sleeper by a fastening system, and this is where a large part of the long-term ride quality is decided. A complete set of railway fastenings and accessories normally includes tie plates, rail clips and clamps, rail anchors that stop the rail creeping longitudinally, rubber pads that damp vibration between rail and sleeper, and the screws and bolts that hold it all together. Fastenings are chosen to match the rail profile, so the fastening specification and the rail specification have to be settled together.
Rails are specified by profile, steel grade, hardness and delivery length. Heavier profiles carry heavier axle loads and higher speeds; harder grades resist wear and rolling-contact fatigue on curves and heavy-haul routes. Longer delivery lengths mean fewer joints to make on site.
| Profile | Weight | EN grade / standard | GOST grade / standard | Length (EN / GOST) |
|---|---|---|---|---|
| 60E1 | 60.21 kg/m | R260, R350HT — EN 13674-1:2020 | DT350VS, DT370IK — GOST 8161-75 | 25–120 m / 12.5–25 m |
| 60E2 | 60.34 kg/m | R260, R350HT — EN 13674-1:2020 | DT350SS, DT370IK — GOST 8161-75 | 25–120 m / 12.5–25 m |
| R65 | 64.72 kg/m | R260, R350HT — EN 13674-1:2020 | DT350NN, DT370IK — GOST 8161-75 | 25–120 m / 12.5–25 m |
| R50 | 51.51 kg/m | R200, R220 — EN 13674-1:2020 | DT260, DT290 — GOST 8161-75 | 12–36 m / 12.5–25 m |
In practice, a heavy mainline or port line is built with 60E1, 60E2 or R65 railway rails, while R50 — 152 mm high, with a 70 mm head, a 132 mm base and a 16 mm web — remains the sensible choice for medium-load regional and industrial tracks. Because R65 can be rolled up to 120 m, specifying long rails at the procurement stage directly reduces the number of joints that have to be made, inspected and maintained for the rest of the line's life.
A joint is a discontinuity, and a discontinuity is where the track fails first. There are two ways of dealing with that.
Bolted joints use railway fish plates bolted through the rail web on both sides. Their double-headed shape clamps the rail ends together, minimises the gap and reduces the vibration that moving trains generate. A 1R65 plate is 1000 mm long with six bolt holes in K54/E54 steel to GOST 8193-73, GOST 33184-2014 and EN 10025-2:2019; a 2R65 plate is 800 mm with four holes in M54 steel to GOST 33184-2014. Bolted joints are quick to install, easy to dismantle and well suited to temporary, industrial and low-speed track.
Welded joints remove the discontinuity altogether. Flash-butt welding fuses rail ends into continuous welded rail, eliminating the gaps and pressure points at each joint, extending rail life and giving a noticeably smoother and safer ride. This is done with rail flash-butt welding machines, either stationary in a welding plant or mobile in the track. Continuous welded rail has one condition attached: thermal movement has to be managed, which is why expansion joints are used on bridges and at the ends of long welded sections.
Turnouts are what turn a line into a network. Station throats, depots and industrial junctions are built up from railway switches and turnouts — ordinary, curved and symmetric turnouts, single and double crossovers, diamond crossings, derailing switches and expansion joints. They are specified by rail profile, gauge and crossing angle: 1:9, 1:12 or 1:14 under EN 13232 at 1435 mm, or 1/9 and 1/11 under GOST 33535-2015 at 1520 mm, with crossings in cast Mn13 austenitic manganese steel or 110G13L to GOST 7370. Turnout lead times and geometry are usually the critical path at any station, so they belong in the procurement plan from day one.
Bridges, viaducts and tunnels are built where the terrain gives no alternative, and they set the clearances the rest of the design has to respect. Signalling, interlocking and traffic control follow, allowing both automated management and operator intervention. Finally the whole line is inspected and tested with modern test equipment — geometry, rail integrity and trial running — before it is accepted for service. The reconstruction of the Sumgayit–Yalama railway line is a working example of these stages executed on an operating corridor.
A pure contractor sells works. The client, or a separate trading company, buys the rails, turnouts, fastenings and welding equipment, and the client carries the risk when a delivery slips, a profile does not match the fastening, or a certificate is missing at inspection.
A supplier-contractor delivers materials and works under one contract. The practical difference shows up in three places: specification (rail profile, fastening type and turnout geometry are made consistent before anything is ordered), interface risk (a single party is accountable when material and installation do not fit), and sequencing (deliveries are planned against the construction programme rather than against a separate purchase order). IB Group works this way, combining supply of permanent-way materials with construction, and adding project management services where a client wants the whole programme run under one responsibility. Scope, quantities, standards and schedules are confirmed per project at the quotation stage — send the alignment, design speed, axle load and gauge to our team through the contact page and the specification can be worked out from there.
Railway construction runs in a fixed order: survey and setting out; earthworks, formation and drainage; sub-base and ballast; sleepers and fastening systems; rail laying; jointing, either bolted with fish plates or flash-butt welded; turnouts at station throats and junctions; bridges, tunnels and culverts where the terrain requires them; signalling and traffic control; and finally inspection, testing and commissioning. Each stage depends on the previous one being completed correctly, which is why defects in earthworks or drainage keep reappearing as track geometry problems long after the line has opened.
Longer rails mean fewer joints, and joints are where wear, noise and maintenance concentrate. Under EN 13674-1:2020, 60E1, 60E2 and R65 profiles can be delivered in lengths of 25 to 120 m, while GOST 8161-75 supply is typically 12.5 to 25 m and R50 is available in 12 to 36 m. On a mainline being built with continuous welded rail, specifying long rails reduces the number of field welds needed; on industrial or temporary track, shorter rails with bolted joints are often the more practical choice.
Gauge is the distance between the inner faces of the two rails, and it determines sleepers, fastenings, turnout geometry and rolling stock compatibility. 1520 mm is the gauge of the post-Soviet network, including Azerbaijan, and its permanent-way products follow GOST standards such as GOST 8161-75 for rails and GOST 33535-2015 for turnouts. 1435 mm is standard gauge, used across the European Union and specified to EN standards such as EN 13674-1:2020 and EN 13232. Gauge has to be fixed at design stage, since every downstream component is ordered against it.
A turnout is an assembly, not a component: switch rails, a crossing, base plates, blocks and an operating mechanism, all built to one crossing angle and one rail profile. It cannot be adapted on site the way plain track can, and station layouts are designed around specific crossing marks — 1:9, 1:12 and 1:14 to EN 13232, or 1/9 and 1/11 to GOST 33535-2015. Because the geometry has to be right before the surrounding track can be laid, turnout specification and delivery usually govern the programme at every station and junction.
Yes, and on railway projects it is usually the lower-risk arrangement. When the same party supplies rails, turnouts, fish plates, fastenings and welding equipment and carries out the construction, rail profile, fastening type and turnout geometry are made consistent before anything is ordered, and deliveries are planned against the construction programme. IB Group combines permanent-way supply with railway construction works and can extend this to project management. Commercial terms, quantities and schedules are confirmed per project at the quotation stage.

13 Sep 2026
What API 5CT actually covers, why threads sit in API 5B, where API 5L begins, how J55 to P110 grades read, how LTC, BTC, EUE and premium connectors differ, and what to require on delivery.

10 Sep 2026
What a fish plate in railway track does, how the double-headed section clamps a rail joint, 1R65 and 2R65 sizes and weights, EN versus GOST steel grades, and how to match a plate to your rail profile.

07 Sep 2026
Which valve family fits which duty, how pressure and temperature decide between carbon and stainless steel bodies, what API 6D, EN 12516, EN 593 and GOST 33259 govern, and the checklist to send with an enquiry.