About usProductsServicesProjectsCareerNewsBlogVideosGallery
  • About us
  • Products
  • Services
  • Projects
  • Career
  • Media
Contact us

IB Group acts as a key strategic partner in the region, providing high-quality products and services in the railway, energy, and oil and gas sectors. The company supports sustainable development by offering innovative solutions in compliance with global standards.

About us
  • About company
  • Our partners
  • Career
  • News
Products
    Services
      Projects
        Contact us
        • + 994 (99) 274 99 99+ 994 (12) 436 52 10
        • [email protected]
        • Babek Plaza floor 11, Baku, Azerbaijan
        Privacy Policy

        ©2026. All rights reserved - IB GROUP OF COMPANIES

        Website development—ONE studioHosting—Best Host
        • IB Group
        • Blog
        • Oil and Gas Piping Supply: How to Choose the Right Pipe
        Oil and Gas Piping Supply: How to Choose the Right Pipe

        Oil and Gas Piping Supply: How to Choose the Right Pipe

        07 Sep 2026

        Oil and gas piping supply begins with a question about duty, not price: what the pipe has to carry, at what pressure and temperature, and whether it sits downhole, in a boiler house, on a rack or buried under a road. Once that is settled, the standard, the grade, the wall thickness and the coating follow almost automatically. This guide shows how to narrow six very different pipe families down to the line item that belongs on the purchase order.

        IB Group supplies pipes for the oil, gas, energy and chemical sectors manufactured in compliance with the API 5L, EN and GOST standard systems, for onshore and offshore work alike. The full range sits on the oil-gas and industrial pipelines page; what follows is the reasoning behind choosing from it.

        The first decision is duty, not diameter

        Buyers who start from a diameter usually end up re-specifying. Start from what the pipe does: these four duty classes barely overlap in metallurgy.

        • Transport and process — crude, gas, water or chemicals at ambient or moderate temperature. Pressure containment and, on buried lines, external corrosion protection dominate.
        • Thermal — steam and hot water in power plants and petrochemical complexes. Creep resistance at temperature dominates, and the grade matters more than the wall.
        • Downhole — casing and tubing inside a well, where axial load, collapse, burst and the connection decide the specification. This is the world of API 5CT.
        • Buried and submerged — the outside of the pipe is attacked as hard as the inside, so coating and insulation become the engineered part of the product.

        Six pipe families in oil and gas piping supply

        The table sets out the six families IB Group supplies, by EN and international specification. GOST equivalents are treated separately below, being a parallel system rather than a translation.

        Pipe familyStandardsDiameterWall thicknessMaterialsTypical duty
        High-pressure boiler pipesEN 10216, ASTM A335Ø10–530 mm2–80 mm15CrMoG, 12Cr1MoVG, P91Power plants, steam systems, petrochemicals; to 620 °C
        Casing and tubing (OCTG)API 5CT, ISO 11960Ø10–406 mm5–25 mmJ55, K55, N80, P110Oil and gas wells, deep drilling, borehole protection
        Seamless steel pipesEN 10216, EN 10297Ø6–711 mm1–40 mmP235GH, P265GH, 15Mo3High-pressure gas and water lines, petrochemicals, heat pipes
        Anti-corrosion coated pipesEN ISO 21809-1, EN 10289Ø20–1200 mm3-layer PE or FBE coatingCarbon steel with applied coatingWater and gas lines, marine infrastructure, chemicals; to 150 bar
        Coated and insulated pipesEN 253, EN 10217Ø20–1600 mm3–20 mmPolyurethane foam, PE or PP jacketBuried and marine lines, oil and gas transfer, heating systems
        Special purpose pipesEN 10255, EN 10296Ø10–1200 mm1–30 mm316L, 321, Inconel 625Aggressive chemical media, high-temperature and specialised service

        Seamless or welded

        A seamless pipe is pierced and rolled from a solid billet, so it has no longitudinal weld and no heat-affected zone along its length. That removes the most common initiation site for cracking under cyclic pressure, which is why seamless product dominates high-pressure, high-temperature and sour service — and why its diameter range tops out sooner. IB Group's seamless line runs to Ø711 mm under EN 10216 and EN 10297, and to Ø720 mm under GOST 8731-74 and GOST 8732-78.

        Welded pipe is the economical answer above that size and is sound for transport duty with a non-aggressive medium at moderate pressure. The insulated family shows the trade-off: the EN 253 carrier pipe is a welded pressure pipe to EN 10217, which is what makes the Ø1600 mm end of that range possible. For steel pipe in large-diameter networks the seam is rarely the limiting factor — the coating usually is.

        Choosing a grade by temperature and medium

        Grade selection is where most re-orders originate:

        • Moderate temperature, general pressure service — P235GH and P265GH cover the bulk of ordinary process and utility lines, and are the workhorse grades of the seamless pipe range.
        • Elevated temperature — molybdenum and chromium-molybdenum grades resist creep, the slow deformation carbon steel suffers under sustained load at heat. 15Mo3 opens that ladder; 15CrMoG, 12Cr1MoVG and P91 carry the boiler range to 620 °C. The GOST boiler line, in grades 20, 12X1MΦ and 12X2MΦ, is rated to 560 °C — a difference that matters when a legacy plant is extended rather than replaced.
        • Corrosive and chloride-bearing media — austenitic stainless 316L and 321, and nickel alloy Inconel 625, where carbon steel would not survive the chemistry at any wall thickness.
        • Downhole strength grades — J55, K55, N80 and P110 are strength classes, not corrosion classes, and follow the load case of the well.

        Handling and inspection equipment is specified alongside the pipe; cranes and inspection machines sit on the machinery and equipment page.

        Coatings and insulation for buried and offshore lines

        Once a pipe goes underground, its service life is governed by what is on the outside. Anti-corrosion coated pipes to EN ISO 21809-1 and EN 10289 carry a three-layer polyethylene or fusion-bonded epoxy coating, are supplied from Ø20 to Ø1200 mm, and are rated for −30 to +100 °C at up to 150 bar; the GOST epoxy and polyurethane equivalents run Ø25–1000 mm, −40 to +120 °C and up to 180 bar — a wider temperature band that matters in continental climates.

        Coated and insulated pipes to EN 253 are a different product: polyurethane foam is injected between an inner carrier pipe and an outer casing under a polyethylene or polypropylene jacket, giving thermal performance as well as corrosion protection across Ø20–1600 mm. These are the pipes used for district heating, buried construction and marine water and gas pipe runs. Whichever is chosen, budget for field joints: factory coating stops short of the ends, and site-made joints are where buried lines fail first.

        EN, GOST and API are parallel systems, not a ranking

        Projects in Azerbaijan and the wider CIS routinely mix all three. A refinery upgrade may run new EN-specified process lines into a plant whose network was built to GOST, while the wells feeding it are on API product. None is "better"; they differ in how chemistry is expressed, how testing is defined and how tolerances are written, which is why grade equivalence is always approximate. Specify one system per line, and state the interface points explicitly.

        That interface work is contractual as much as technical: the wording of the technical annexes decides who carries the risk of a mismatch, which is why contract support services and project management sit alongside supply rather than after it. IB Group's work on pipeline and valve supply for the Heydar Aliyev Oil Refinery and on the Azərkimya pipeline renewal are examples of supply into existing industrial networks.

        What a complete piping enquiry states

        A quotation is only as good as the enquiry behind it. A complete request states:

        • Medium and its composition, including sour service and chloride content;
        • Design pressure and temperature, plus the operating range if it differs;
        • Outside diameter and wall thickness, or the pressure class to size against;
        • Standard system and grade — EN, GOST or API, and the grade within it;
        • End finish — plain end, bevelled or threaded, and for threaded product the connector type;
        • Coating and insulation requirements, including field joint scope;
        • Quantity, delivery point and inspection, with the documentation package expected.

        Valves are specified against the same duty data, so sending the pipe and oil-gas and industrial valves requirements together saves a round trip. Pricing and delivery are confirmed per order at the quotation stage — send the parameters above through the contact page and the technical team will respond with a specification and an offer.

        Frequently asked questions

        What is the difference between seamless and welded pipe in oil and gas piping supply?

        A seamless pipe is formed from a solid billet and has no longitudinal weld; a welded pipe is formed from plate or strip and joined along its length. Removing the seam removes a common crack initiation site, which is why seamless product is preferred for high pressure, high temperature and sour service, while welded pipe is more economical at large diameters. IB Group's seamless range covers Ø6–711 mm to EN 10216 and EN 10297; welded carrier pipe to EN 10217 underpins the insulated range to Ø1600 mm.

        Should I specify EN, GOST or API for a pipeline in Azerbaijan?

        All three are supplied and all three are valid; the choice follows the existing network and the project specification rather than technical superiority. If the line ties into a plant built to GOST, staying within GOST simplifies spares, welding procedures and inspection, while new-build process and transmission lines are commonly specified to EN or API 5L. Specify one system per line and define the interface points, because grade equivalences are approximate.

        Which pipe is used for a buried gas pipeline?

        A buried line needs external protection engineered as part of the product. Anti-corrosion coated pipes to EN ISO 21809-1 and EN 10289, with three-layer polyethylene or fusion-bonded epoxy coating, are supplied from Ø20 to Ø1200 mm for −30 to +100 °C at up to 150 bar; GOST epoxy and polyurethane equivalents are rated −40 to +120 °C and up to 180 bar. If thermal performance is also needed, EN 253 insulated pipes cover Ø20–1600 mm, and field joint protection belongs in the scope.

        What pipe handles high-temperature steam?

        High-pressure boiler pipes are the family designed for it. Supplied to EN 10216 and ASTM A335 in Ø10–530 mm with walls from 2 to 80 mm, they use creep-resistant grades 15CrMoG, 12Cr1MoVG and P91 and are rated to a maximum of 620 °C. The GOST equivalent, in grades 20, 12X1MΦ and 12X2MΦ, covers Ø16–426 mm with walls of 2–36 mm and a maximum of 560 °C. That temperature difference is usually the deciding factor when uprating an existing boiler house.

        What information does IB Group need to quote piping?

        State the medium and whether the service is sour, the design pressure and temperature, the outside diameter and wall thickness or the pressure class to size against, the standard system and grade, the end finish and connector type, any coating or insulation requirement including field joints, and the quantity, delivery point and documentation package expected on delivery. The technical team can then specify from the pipe range; price and delivery schedule are confirmed per order at the quotation stage.

        Other articles

        API 5CT Casing and Tubing: A Buyer's Guide to the Standard

        13 Sep 2026

        API 5CT Casing and Tubing: A Buyer's Guide to the Standard

        What API 5CT actually covers, why threads sit in API 5B, where API 5L begins, how J55 to P110 grades read, how LTC, BTC, EUE and premium connectors differ, and what to require on delivery.

        Fish Plate in Railway: Function, Sizes, Weights and Steel Grades

        10 Sep 2026

        Fish Plate in Railway: Function, Sizes, Weights and Steel Grades

        What a fish plate in railway track does, how the double-headed section clamps a rail joint, 1R65 and 2R65 sizes and weights, EN versus GOST steel grades, and how to match a plate to your rail profile.

        Industrial Valves for Oil and Gas: Types, Standards and How to Specify Them

        07 Sep 2026

        Industrial Valves for Oil and Gas: Types, Standards and How to Specify Them

        Which valve family fits which duty, how pressure and temperature decide between carbon and stainless steel bodies, what API 6D, EN 12516, EN 593 and GOST 33259 govern, and the checklist to send with an enquiry.